+- Sinisterly (https://sinister.li)
+-- Forum: Computers (https://sinister.li/Forum-Computers)
+--- Forum: Operating Systems (https://sinister.li/Forum-Operating-Systems)
+--- Thread: Limited access!! (/Thread-Limited-access)
Pages:
1
2
Limited access!! - IpLayer - 10-24-2013
Hi,I've Cracked some AP,and I gain the Password,But I can't Connect to the Network!!
In windows it say Limited access,and in linux and samsung Galaxy it stuck on Obtaining IP address..
I've tried to change my mac address to his mac ,but it didn't work
and tried to use static IP:
IP address : 192.168.1.17
subnet mask:255.255.255.0
Defaul gateway:192.168.1.1
Didn't work either..
When i connect in limited access the autoconfiguration IP4 being like : 169.254.70.2
IPv4 subnet mask 255.255.0.0
the signal is fair in windows and about -84 in commview and about 30% in linux ,I don't think it's signal Problem?!
Any Idea?
Limited access!! - IpLayer - 10-24-2013
Hi,I've Cracked some AP,and I gain the Password,But I can't Connect to the Network!!
In windows it say Limited access,and in linux and samsung Galaxy it stuck on Obtaining IP address..
I've tried to change my mac address to his mac ,but it didn't work
and tried to use static IP:
IP address : 192.168.1.17
subnet mask:255.255.255.0
Defaul gateway:192.168.1.1
Didn't work either..
When i connect in limited access the autoconfiguration IP4 being like : 169.254.70.2
IPv4 subnet mask 255.255.0.0
the signal is fair in windows and about -84 in commview and about 30% in linux ,I don't think it's signal Problem?!
Any Idea?
Limited access!! - IpLayer - 10-24-2013
Hi,I've Cracked some AP,and I gain the Password,But I can't Connect to the Network!!
In windows it say Limited access,and in linux and samsung Galaxy it stuck on Obtaining IP address..
I've tried to change my mac address to his mac ,but it didn't work
and tried to use static IP:
IP address : 192.168.1.17
subnet mask:255.255.255.0
Defaul gateway:192.168.1.1
Didn't work either..
When i connect in limited access the autoconfiguration IP4 being like : 169.254.70.2
IPv4 subnet mask 255.255.0.0
the signal is fair in windows and about -84 in commview and about 30% in linux ,I don't think it's signal Problem?!
Any Idea?
RE: Limited access!! - Boxingfan - 10-24-2013
I understand that this is not related to the post but would you happen to know any good HTML editors?
RE: Limited access!! - Boxingfan - 10-24-2013
I understand that this is not related to the post but would you happen to know any good HTML editors?
RE: Limited access!! - Boxingfan - 10-24-2013
I understand that this is not related to the post but would you happen to know any good HTML editors?
RE: Limited access!! - chmod - 10-24-2013
(10-24-2013, 05:22 PM)Boxingfan Wrote: I understand that this is not related to the post but would you happen to know any good HTML editors?
Stay on topic
RE: Limited access!! - chmod - 10-24-2013
(10-24-2013, 05:22 PM)Boxingfan Wrote: I understand that this is not related to the post but would you happen to know any good HTML editors?
Stay on topic
RE: Limited access!! - chmod - 10-24-2013
(10-24-2013, 05:22 PM)Boxingfan Wrote: I understand that this is not related to the post but would you happen to know any good HTML editors?
Stay on topic
RE: Limited access!! - dR.0xYw0Rm - 10-24-2013
Sometimes that problem it's due to IP address conflicts on the computers, try to Release and Renew an IP Address.
Start > Run > CMD
Code:
ipconfig /renew
ipconfig /releaseAnd you can also refresh all DHCP leases and re-register DNS names using the registerdns command.
Code:
ipconfig /registerdns